11 tons natural gas boiler price
Gas 11 tons boiler price heat loss through the combustion of fuel gas boiler, will release some heat, which will supply part of the user, some will be recycled and part is inadvertently wasted. So these are wasted heat lost through the ways in which it (1) heat losses:? Flue gas exhaust gas boiler part of the heat into the atmosphere, causing the boiler heat losses, it is each boiler term heat loss Dazhong biggest one. The main factors influencing the heat loss is higher exhaust gas temperature and the amount of smoke exhaust gas temperature, the greater the amount of smoke, the greater the heat loss. Low exhaust gas temperature depends mainly on the number and operating conditions of the heating surface; the amount depends on how much leakage exhaust case and the furnace excess air, flue. (2) heat loss incomplete combustion gas: a part of the unburned combustible gas is discharged with the flue gas to heat loss caused by heat in the flue gas. The main factors affecting the incomplete combustion gas heat loss is the excess air and furnace structure. Excess air coefficient is too small, uneven air is mixed with fuel, easy to generate carbon monoxide and other combustible gases; excess air coefficient is too large, the furnace temperature is lowered, the combustible gas is not easy ignition and combustion. Furnace volume is too small, combustible gases in the furnace too late to enter the combustion flue gases caused by incomplete combustion heat loss. (3) heat loss: the furnace heat loss, frameworks, pipes, door opening caused by heat dissipation to the surroundings. Size depends on the heat loss factors of the size of the surface area of the furnace gas steam boiler, heat insulating properties and thickness, the outside air temperature and the flow velocity. Electric heating reactor common external damage: an electrically heated reactor despite external corrosion has a high etching resistance against acid and alkali resistance, but our electrical heating by the heating apparatus is a kettle layer and an outer tire iron constituted. Such a medium is iron acids and bases are not corrosion-resistant. If we would have the production process if the reactor cover or screwed pipe joints without seal failure or leak acid tire iron reactor apparatus for electrically heating the outer corrosion. Corrosion support member 2. The reactor was heated electrically heated reactor during installation, support or other support member may be mounted directly on the floor, due to the long manufacturing operations on the floor may be deposited with corrosive media, so that for support our reactor electrically heated apparatus corrosion, resulting in the supporting force of each of the support produces a change resulting in a change in stress in the damage produced during heating layer. 3. The electrically heated reactor stress spout in the electrically heated reactor, when the steel of the pipe and the pipe joint, since the thermal deformation and the reaction was heated electrically heated autoclave vessel or duct stressed cold might damage the pipe.
After the 11 tons boiler price high cost of it? That renovation work is currently boiler have been carried out in various provinces and cities, many users are willing to transform doubt there will be a point, that is the high cost after the boiler yet? Then we took the coal-fired gas boiler renovation project for analysis. During the transformation of the former coal-fired boilers, there will be some need for coal storage, transportation costs, low operating efficiency of the boiler, the boiler thermal efficiency loss, loss of fuel costs caused by production costs caused by the loss of non-compliance; Then there will be coal-fired processing costs pollutant emissions boiler; and a lot of maintenance costs and labor costs continue to treat boiler site troubleshooting, and accounting of these costs are relatively high. After that say transformation, gas boilers belong first and foremost clean energy, to some extent, less waste emissions, it will save some gas treatment costs; In addition, the auxiliary gas boiler system more orderly is not complicated, so the run is relatively stable , operating efficiency is relatively high, so will enhance the operational boiler thermal efficiency to a certain extent, there is some improvement on return loss and the cost of fuel; at the same time, gas boiler this would not take up space, just to ensure perimeter clean can be, relatively speaking, save some labor costs, probably in terms of fuel, natural gas will be slightly more expensive than some of the coal, but the longer term, energy-saving effect of natural gas boilers, will be a period of time, return this part of the difference in money, but if management properly, will reach back to the results. After so the cost after the boiler strictly speaking, is not elevated, a certain time, will achieve cost reduction.
Beijing New Energy Automobile Co., Ltd. is China's first to operate independently and gain new energy automobile production qualification of new energy auto companies, mainly engaged in new energy vehicles and key parts and components research and development, production, sales and service business segments, and the layout intelligent manufacturing, energy management, smart travel, Internet +, and other strategic emerging industries. In the new energy automobile manufacturing process, and a series of paint drying processes can not do without the help of hot water 11 tons boiler price. Due to the company before the device has reached less than the growing production needs, the introduction of the 2017 mid-tail electric company producing heating pressure hot water boiler (CEDR0.7--95 / 70-Ⅱ).
The difference of fuel between Oil-fired Boiler and Gas-fired BoilerOil-fired 11 tons boiler price refers to the fuel-fired boiler, including diesel oil, waste oil and other oil boilers. The overall arrangement of the oil-fired boiler is similar to that of the coal-fired boiler, except that the bottom of the furnace of the oil-fired boiler is mostly made into the bottom of the insulation furnace with a tilt to the back wall of 10 °~ 30 °, in order to obtain good combustion characteristics. In order to atomize fuel oil, there are two types of fuel burner nozzle: mechanical centrifugal injector and steam atomized Y type injector. The fuel of the oil-fired boiler is the fuel (such as diesel oil, kerosene, etc.). The fuel of the gas-fired boiler is gas (such as natural gas, city gas, biogas, etc.), depending on what fuel the boiler burns. The difference between a fuel-fired boiler and a gas-fired boiler is what kind of fuel burners are used to burn the gas-fired boilers, which are called gas-fired boilers, oil-fired boilers with fuel-fired burners, and oil-fired boilers called oil-fired boilers.