Safe And Reliable Industrial Coal Fired Steam Boiler
Due to the special nature of the industrial park location, we are more to consider whether the boiler with green features in the choice of boiler equipment. According to our survey of the entire boiler industry, quick side has considerable experience in research and development in the field of environmental cleaning boilers, boiler equipment while also providing low pollutant emissions for Beijing more enterprises and institutions, we are fully confident that the fast boiler ability. --customer feedback
Boiler startup startup boiler combustion adjustment method should pay attention to the flame monitoring, combustion and make adjustments as follows: (1) correct the ignition. Adequate ventilation furnace before ignition, the ignition first investment ignition device (or torch), then turn the gun. (2) diagonally administered fire mouth, pay attention to timely switch, the flash point was observed nozzle suitable fire, flame sought uniformly distributed in the furnace. (3) to adjust the lead note, air volume, furnace pressure should not be too large. (4) in particular to monitor exhaust gas temperature when combustion instability, the occurrence of the back pass to prevent the secondary combustion. (5) to maximize the temperature of primary air, secondary air is fed reasonable depending on the fuel. Adjusting the temperature difference between both sides of the cigarette. Do pulverizing system-OFF stable (6) operation. Stoker coal under stable powder machine speed and stability. Coal with wind stability and oxygen stable. Steam temperature, steam pressure increase stability and load stability liter.
Mill safe and reliable industrial coal fired steam boilers to reduce pollution which method 1, leak checking and maintenance of protection: 2 mm steam leakage will cause energy losses of more than 10 tons of coal each year do? When you do not use it, you can turn it off to save energy. For water, steam and compressed air leak survey and routine maintenance, cost very little. 2, the non-contact cooling water in repeated use: Since the non-contact cooling water temperature and the quality is very good, it can be reused for desizing, scouring, rinsing and other processes. Three best source of cooling water is regenerated: sintering machine, a pre-link and compressor systems. The plant water recovery system may be installed, pipes, valves, storage tanks, and control systems. 3, reuse of steam condensate: textile mills require large amounts of saturated water vapor in the dyeing process, wherein a portion of the condensate is converted to its high temperature and purity. Water can be pumped back to the boiler to form a new steam. For those who buy steam from suppliers, or boiler is located away from the dyeing process, the condensate can be used as water washing or desizing. 4, pre-treated wastewater reuse Procedure collected bleaching, mercerizing machine, the water can be reused in other programs, there is no direct discharge of wastewater. 5, hot wash water is recovered from the hot gas in the dyeing process, large amounts of hot water are used to wash. Heat the washing water can be collected by the system plate heat exchanger to preheat the water to be sent to the next washing. 6, pre-screened coal enterprises should introduce screening spiral coal boiler technology to selection of raw materials. It is possible to improve the media tell the good, the bad quality of proportion, to avoid loss of small volumes of coal and coal calorific value. 7, maintaining steam traps traps can help maintain effective delivery of the steam plant. The valve is removed from the steam pipe and prevent further condensation water, so as to avoid heat loss and reduce fuel consumption. 8, pipe insulation pipes, valves and flanges, valves and flanges experience hot waste of resources, reducing efficiency. Steam delivery device insulated to prevent vapor loss is an inexpensive, energy-saving method of .9, the heat recovery boiler chimney smoke at a temperature of 360 deg.] C, and sometimes directly discharged into the atmosphere, there is no heat recovery. In fact, this heat can be used to preheat boiler water, steam or create a new steam system. 10, optimization of compressed air systems consume a large amount of compressed air in many parts of textile machines Mills. These instruments are prone to leakage, particularly in a threaded joint, rubber joints, valves, automatic regulator, the inflatable device and the old gasket. In addition, the use of compressed air pressure is usually based on the maximum pressure setting; reduce this pressure is feasible and would not have any negative impact manufacturing.
Features of Chinese small electric boiler electric boiler has been continuously research new self, to the quality of the first, which has been pre-sales service our customers receive the praise, its research department has developed the latest technology and electric control system, economy , energy saving, environmental protection, security and other aspects of the world-class level. First, the introduction of an electric boiler, electric boiler automatic intelligent control techniques, unattended; 2, electric boiler work in a flexible manner, can be set to manual or automatic mode; 3, electric boiler can also need to set the automatic start date boiler , working hours, one day can be set ten different working periods, the boiler automatic, time to start each of the heating elements, the heating element switching cycle, the respective contact time, the same frequency, improving equipment life; 4, electric boiler analog control algorithms: automatic temperature (pressure) the PID, calculation, tracking, to ensure that the pump, the circulation pump start and stop automatically when the load change; can also be manually controlled; 5, chain-closing function; 6, alarm function: abnormal situation , automatic alarm; bell alarm is released, without exclusion of the fault, the alarm again; 7, appearance: boiler packaging with embedded frame structure, the entire outer surface of the spray, delicate and beautiful; 8, environmental run: no noise, pollution, high thermal efficiency, high quality and efficient boiler insulation materials, small heat loss, thermal efficiency greater than 98%; 9, compact, rational design and professional Into the manufacturing process, of the small boiler area, saving space; 10, range (electric hot water boiler, electric safe and reliable industrial coal fired steam boiler, electric storage boilers). 11, affordable, new electric boiler regardless of price, quality, lot better than the old-fashioned on environmental protection. Second, the characteristics of the boiler main body 1, made of high quality steel boilers, industrial boilers according to the manufacturer specifications painstakingly created; 2, vertical furnace, girth welds are welding, vertical boiler, X-ray detection girth weld; 3, using the boiler body quality and efficient insulation material, heat loss, thermal efficiency greater than 98%. 4, electronic control box and boiler complete supply, easy to install. 5, the heat-sensitive semiconductor material for high-tech heating body, a high electric conversion efficiency (97%) of coal up more than 20% cost savings, fuel savings of up to 40%. Power 1 minute heater hot water circulating from the tank to the radiator outlet temperature is above seventy degrees, thirty minutes radiator temperature of more than seventy-five. This is the use of non-pressure boiler circulating water heating system, a machine belt, not dry, is the development trend of modern boiler.