fuel water tube boiler
Boiler company in malaysia
ZG Boiler has been closely involved in boiler since its inception in 1945. It was formerly know as ZG Boiler. ZG Boiler also supply to industrial boiler export to regional countries like Middle East, Japan, China, Malaysia, Indonesia, India, Thailand, Singapore, Australia etc. In 2014, ZG boiler company in Malaysia have cooperated with six company with seafood factory, paper mill, Palm Oil Mill, PVC mfg, Plywood. Boiler price in Malaysia, please contact our online service.
1. To determine the heating of the tank, no more open to other pipelines and storage tanks, to avoid heating invalid.
2, the heating process of heating the object to be inspected, after the shutdown temperature in place in a timely manner to avoid unnecessary waste.
3, the production team must not be indiscriminate tune the burner, incorrect combustion of natural gas will make the incomplete combustion or combustion heat loss.
4. To see a gas-fired boiler flue gas temperature gauge regularly and records and found that abnormal temperature boiler to check immediately, whether in normal operation, and report to management.
Henan gas fuel water tube boiler installation requirements for the gauge 1. Pressure gauge installation should meet the following requirements: ⑴. Henan gas boiler installation position gauge, should be easy to observe and rinsing, the dial should be tilted forward 15 °, and should prevent affected by temperature, vibration and the like freezing. ⑵. There should be a trap between the pressure gauge and gas-fired boiler drum Henan. Steam or hot water in which the spring and then into the cooling pipe, to avoid reading errors caused by high temperatures, even damaged parts in the table. The inner diameter of the trap, with the brass when not less than 6mm, when using steel not less than 10mm. A lower portion of the trap, preferably equipped with drain cocks, water to let go of the tube after shutdown. ⑶. It should be fitted between the water gauge and the three-way stopcock elbow, and to flush the pipeline inspection, check, unloading gauge change. a. When normal working pressure gauge, Henan gas boiler media through the trap and pressure gauge connected, the pressure gauge pressure boilers. b. Check the pressure gauge, Henan gas boiler and pressure gauge cut off, the pressure gauge to the atmosphere, because there is no pressure in the table, so if the pointer back to zero can not prove that the gauge has failed and must be replaced. c. When flushing the trap, Henan gas boiler with the atmosphere, with the pressure gauge cut off, the trap in the water and dirt, the boiler blowing in the media. d. So that when water in the trap, the trap and the air pressure gauge are cut off, Henan gas boiler steam or hot water is gradually accumulated in the trap was cooled. e. When checking pressure gauges, while communicating with the boiler working pressure gauge and check the pressure gauge. Standard gauge calibration connected with the flange on the left side of the three-way cock, the medium from the working pressure into the trap and simultaneously checking the pressure gauge. Pressure gauge indicates the two values, the difference shall not exceed the gauge tolerances specified otherwise, the work proved inaccurate pressure gauge, pressure gauge must be replaced. Three-way stopcock handle end portion, the plug must be marked with an arrow indicating the direction of passage in order to identify. When the three-way stopcock operation, action to slow, to avoid damaging the gauge parts. ⑷. Even if long tube pressure gauge, the valve can be installed (or cock) close to the connection pipe at boiler drum Henan gas for use in the maintenance of the cutting gauge and accessories. However, in operation, the valve must be loaded (or tap) the hand wheel (or handle) Remove or lock to prevent accidental off and cause a major accident. 2. When the pressure gauge of the following circumstances, should stop using: ⑴. Limited nail no pressure gauge, the staple rotation pointer does not return to the limit; not limitation staple no pressure gauge, a pointer value from the zero position more than a predetermined tolerance gauge. ⑵. The surface of the glass or ambiguous dial scale. ⑶. No seal, the seal is damaged, or the Verify the expiration date. ⑷. In the table pointer leaks or beating. ⑸. Other effects gauge accurate defect.
Fangkuai Company has a fully-automatic PLC intelligent control system designed and developed by itself with complete intellectual property rights. It adopts a combination of mechatronic control equipment and a programmable logic controller (PLC). Take the advanced programmable logic controller (PLC) as the "central processing unit" of the control system. The control system is operated through the touch screen, which greatly improves the degree of automatic control and operation reliability of the fuel water tube boiler, and the operation is simpler and more intuitive.