industrial usage 4 ton coal fired steam boiler
The third reason is that the amount of nitrogen oxide released during operation is very small. Most heating equipment such as ordinary boilers need to use coal materials as raw materials when they are in operation. Materials such as coal generally release a large amount of hazardous air-quality substances when burned. The condensing boiler uses the steam produced by natural gas combustion as the raw material when it is in operation, so the nitrogen oxide content released during the operation is much lower than the prescribed standard. The analysis of the reason for the year-by-year increase in the sales of condensing boilers has come to an end for the time being.
6 tons adjusting a combustion gas industrial usage 4 ton coal fired steam boiler, normal combustion boiler three basic aspects of indicators include a uniform supply of the fuel, reasonable ventilation, adjustment the combustion. 1, to maintain the high temperature of the combustion chamber temperature of the upper layer is preferably in the 1100 ~ 1300 ℃, flame orange in color. Flame reddish color indicates that the amount is not enough to the wind, the color white indicates that excessive wind. It should be appropriately adjusted. 2, fuel ash to reduce ash content in the combustibles to be below 10%. 3, reducing the temperature of the boiler flue gas exhaust gas temperature should be controlled below 200 ℃. 4, holding furnace negative excess air boiler is 1.2 to 1.4, by adjusting the balance of the blowers to maintain the furnace pressure is -20 ~ -30Pa. 5, the thermal efficiency of the boiler to improve the thermal efficiency of the boiler should be kept above 60%. II. Combustion Adjustment 1, the amount of fuel to air required for combustion and the amount of a reasonable distribution. Ventilation should first increase the amount of fuel increases, it should first reduce the amount of fuel supply reduced ventilation. 2, the thickness of the seam and seam thickness configuration grate speed is 80 ~ 120mm grate speed at high, middle and low profile configuration of several commonly used methods:. 9a rapid combustion of thin seam b c thick seam in low combustion. 3 thick seam combustion speed, the segment with the wind blowing principle: burn promoting intermediate ends. That is, after the coal into the coal starts to warm up the shutter, fire line front arch, the primary combustion zone, the middle grate to burn the rear grate zone. Normal combustion conditions are: fuel from the coal at the beginning of the fire shutter 300mm, uniform flames, the fire bed formation, at the end of combustion from the end of the grate 300 ~ 500mm. 4. maintain proper furnace temperature to avoid coking. The fire bed to maintain the homogeneous combustion, to avoid burning fire bed obliquely. 6. The residence time of the fuel on the grate in less than 30 minutes.
The coal fired industrial usage 4 ton coal fired steam boiler consists of two large boiler drum out of factory , up major possession including boiler body , upper steel frame and furnace wall ,lower bulk including coal bucket ,chain grate ,lower furnace wall, and internal ventilation tube. Fuel: Bituminous Coal, dry-burning coal, hard coal, ligneous coal, etc.
1.Combustion and both sides of the furnace chamber adopt membrane water-cooling wall structure. With this kind of structure, the boiler has a high heat transmission coefficient, low heat loss, good air tightness, no distortion for furnace wall and no ash leakage.
2.Furnace front and rear water wall tube extend down to the upper portion of the grate and form the front and back arch, which extends the span of arch.
3. Inverted “α” arch furnace technology makes the front arch high and short, rear arch low and long. This structure increases the burning time of the flue gas in the furnace so as to improve the combustion efficiency. Besides, the streamline shape of back arch can throw the left carbon grains from the back furnace grate into the front so that the coal is easier to get ignited. Finally, many types of coal can be applied in the boiler.
4.The length of the front and back shaft is longer than the other domestic ones, which prolongs the time of fuel combustion in the furnace and lower the carbon content in the furnace slag. Thus, the overload ability of the boiler is strengthened with the increased effect area of furnace grate.
AMD Power were to buy 10 tons of steam and one 4 tons of steam condensing industrial usage 4 ton coal fired steam boiler fuel gas from the company for cell processing company production and construction. From the analysis of the demand to the boiler factory, by the company solely responsible for AMD Power fully demonstrated the company's confidence in me, the smooth progress of bilateral cooperation.