the fuel is biomass oil and gas fired boiler shipped to argentina
The Fangkuai Group's unique full-operating the fuel is biomass oil and fired boiler shipped to argentina operation laboratory has an annual operating cost of more than 5 million yuan, which can simulate the operating conditions of various types of boilers under multi-operating environment conditions. The laboratory provides technical tests such as test and inspection, analysis and evaluation, data evaluation, energy saving and environmental protection, and special software from materials to complete equipment, hardware to software, and even complex large systems.
After gas-fired the fuel is biomass oil and fired boiler shipped to argentinas for low-nitrogen transformation impact: environmental protection efforts continue to increase, the provinces and cities have introduced various environmental policies. Air pollutant emissions is one of the main issues of governance and environmental protection sectors. For gas-fired boilers for low-nitrogen transformation has also become popular, such as Beijing, Tianjin, Zhengzhou, Xi'an and other places are carrying out renovation work and out of the boiler. Natural gas as a clean energy, can be reduced nearly 100% of the sulfur dioxide and dust emissions, 60% of carbon dioxide emissions and 50% of nitrogen oxide emissions, and help to reduce acid rain, global warming alleviate, reduce proportion of the amount of coal energy important energy; corresponding gas boiler has gradually been used and popular. But not as long as the use of gas-fired boiler can, according to China's introduction of the latest air pollutant emission standards, Beijing and Tianjin, the Yangtze River Delta and other regions, and Zhengzhou, Xi'an and other cities ever to perform the most stringent air pollutant emission standards --30 mg / cubic meter. Many enterprises due to gas-fired boiler installation time relatively early, current nitrogen oxide emissions higher than this standard, however, when the burner exhaust emissions can not meet the standards formulated by the state, need to deal with the transformation of low nitrogen may continue to be put into use .
Air & Gas Circuit – we know that air is one of the main components of the fire triangle and hence necessary for combustion. Since lots of coal is burnt inside the the fuel is biomass oil and fired boiler shipped to argentina it needs a sufficient quantity of air which is supplied using either forced draught or induced draught fans. The exhaust gases from the combustion are in turn used to heat the in going air through a heat exchanger before being let off in the atmosphere. The equipment which handles all these processes fall under this circuit.
Burner fuel gas selected selection principles which fuel gas the fuel is biomass oil and fired boiler shipped to argentina burners should be based on structural features and performance requirements of the boiler body, in conjunction with user conditions, making correct comparison, several general principles according to the following options: 1) according to user selection of used fuel type, liquid fuel kerosene, diesel oil, heavy oil, residual oil and waste oil, fuel gas city gas, natural gas, liquefied petroleum gas and biogas, fuel should have the necessary analysis of data used: ① kerosene, diesel should have heat and density. ② heavy oil, residual oil and the viscosity should, heat, moisture, flash point, mechanical impurities, ash, freezing point, density and the oil temperature. ③ should calorific gas, gas pressure and density. 2) to select the type burner nozzle atomization method or the gas burner and the furnace structure according to the performance of the boiler. 3) the burner output should match the rated output of the boiler, choose a good shape of the flame, such as length and diameter so as to adapt the furnace structure. The required combustion air is supplied from the root flare fuel gas and air or oil mist uniformly mixed rapidly, to ensure complete combustion. The rated output of the boiler and boiler efficiency is determined, the fuel consumption is calculated, and then selected according to power a single burner arranged to determine the number of burners. Increase the number of burners, in favor of the atomization quality assurance wind oil mix, but too many, and not easy to operation and maintenance, will give burner arrangement difficult. 4) adjusting the burner to a large extent, be able to adapt to changes in boiler load, to ensure complete stable combustion under different conditions. 5) fuel atomization less energy consumption, adjusting the wind resistance of the device to be small. 6) Effects of noise and smoke emission must comply with environmental standards, mainly emissions S02, CO and NOx must be lower than the predetermined country, should use low NOx burners and low noise. There are integral and split two 7) a burner assembly embodiment. I.e. monolithic burner body, the burner and a combustion air blower system (including an oil pump, a solenoid valve, a servo motor or the like) into one; split i.e. burner body (comprising a combustion head, oil or gas systems), fans and combustion burner control system (including the control box, fan thermal relay, AC contactor, etc.) are each independent three-part system, according to the specific requirements of the boiler and user choice. Simple 8) should be used in construction, reliable operation, easy to adjust and control the repair, easy to implement automatic control of the combustion process in the burner. 9) to deal with the burner brand, performance, price, and service life of comprehensive comparison. 10) In addition to the burner air pressure to overcome the resistance of the boiler body considered, but also to overcome the resistance and flue gas economizer system.